有机废物厌氧发酵生物合成己酸研究进展

厌氧发酵处理有机废物并合成高价值羧酸盐的技术日趋成熟。尤其是己酸作为产物之一,因其附加值高,易于分离,用途广泛,越来越受到关注。微生物合成己酸需要电子供体及受体。详细介绍了乙醇、乙酸分别作为电子供体、受体合成己酸的机理——逆β氧化反应,总结合成己酸底物以及影响合成的因素（温度、pH值、水力停留时间、竞争路径、氢气分压、底物比例、氮源等）。目前采用科氏梭菌以乙醇为电子供体来合成己酸的技术较成熟,探索了利用乳酸为电子供体合成己酸的代谢机理,并指出开发乳酸转化合成己酸的技术可成为未来发展方向。     

稻壳与聚氯乙烯共热解的特性及动力学

在热重分析仪中进行了稻壳和聚氯乙烯（PVC）的共热解实验,结果显示:在共热解时稻壳开始剧烈热解的温度相比单独热解时大幅度降低,由350℃降至300℃,表明掺入PVC降低了稻壳的热解温度。在升温速率为20℃/min,稻壳和PVC比例为2∶1（质量比）时,混合热解协同效应最明显。3种动力学分析方法均证明共热解现象的存在。利用Coats-Redfern法进行动力学分析,发现共热解活化能普遍较单独热解时低,表明PVC与稻壳共热解有明显的相互作用。利用Ozawa法进行分析,发现转化率为20%~60%阶段下共热解平均活化能值为37.60 kJ/mol,低于稻壳单独热解的平均活化能41.45 kJ/mol。Friedman法分析结果显示对应转化率下共热解活化能均低于稻壳单独热解活化能。稻壳和PVC共热解倾向于反应动力学控制。     

Bioassay: A useful tool for evaluating reclaimed water safety

Wastewater reclamation and reuse has been proved to be an effective way to relieve the fresh water crisis. However, toxic contaminants remaining in reclaimed water could lead to potential risk for reuse, and the conventional water quality standards have difficulty guaranteeing the safety of reclaimed water. Bioassays can vividly reflect the integrated biological effects of multiple toxic substances in water as a whole, and could be a powerful tool for evaluating the safety of reclaimed water. Therefore, in this study, the advantages and disadvantages of using bioassays for evaluating the safety of reclaimed water were compared with those of conventional water quality standards. Although bioassays have been widely used to describe the toxic effects of reclaimed water and treatment efficiency of reclamation techniques, a single bioassay cannot reflect the complex toxicity of reclaimed water, and a battery of bioassays involving multiple biological effects or in vitro tests with specific toxicity mechanisms would be recommended. Furthermore, in order to evaluate the safety of reclaimed water based on bioassay results, various methods including potential toxicology, the toxicity unit classification system, and a potential eco-toxic effects probe are summarized as well. Especially, some integrated ranking methods based on a bioassay battery involving multiple toxicity effects are recommended as useful tools for evaluating the safety of reclaimed water, which will benefit the promotion and guarantee the rapid development of the reclamation and reuse of wastewater.     

Influence of floc dynamic protection layer on alleviating ultrafiltration membrane fouling induced by humic substances

Cake layer formation is inevitable over time for ultrafiltration (UF) membrane-based drinking water treatment. Although the cake layer is always considered to cause membrane fouling, it can also act as a “dynamic protection layer”, as it further adsorbs pollutants and dramatically reduces their chance of getting to the membrane surface. Here, the UF membrane fouling performance was investigated with pre-deposited loose flocs in the presence of humic acid (HA). The results showed that the floc dynamic protection layer played an important role in removing HA. The higher the solution pH, the more negative the floc charge, resulting in lower HA removal efficiency due to the electrostatic repulsion and large pore size of the floc layer. With decreasing solution pH, a positively charged floc dynamic protection layer was formed, and more HA molecules were adsorbed. The potential reasons were ascribed to the smaller floc size, greater positive charge, and higher roughness of the floc layer. However, similar membrane fouling performance was also observed for the negative and positive floc dynamic protection layers due to their strong looseness characteristics. In addition, the molecular weight (MW) distribution of HA also played an important role in UF membrane fouling behavior. For the small MW HA molecules, the chance of forming a loose cake layer was high with a negatively charged floc dynamic protection layer, while for the large MW HA molecules it was high with a positively charged floc dynamic protection layer. As a result, slight UF membrane fouling was induced.     

Plasmonic silver/silver oxide nanoparticles anchored bismuth vanadate as a novel visible-light ternary photocatalyst for degrading pharmaceutical micropollutants

The degradation of pharmaceutical micropollutants is an intensifying environmental problem and synthesis of efficient photocatalysts for this purpose is one of the foremost challenges worldwide. Therefore, this study was conducted to develop novel plasmonic Ag/Ag₂O/BiVO₄ nanocomposite photocatalysts by simple precipitation and thermal decomposition methods, which could exhibit higher photocatalytic activity for mineralized pharmaceutical micropollutants. Among the different treatments, the best performance was observed for the Ag/Ag₂O/BiVO₄ nanocomposites (5 wt.%; 10 min's visible light irradiation) which exhibited 6.57 times higher photodegradation rate than the pure BiVO₄. Further, the effects of different influencing factors on the photodegradation system of tetracycline hydrochloride (TC-HCl) were investigated and the feasibility for its practical application was explored through the specific light sources, water source and cycle experiments. The mechanistic study demonstrated that the photogenerated holes (h⁺), superoxide radicals (?O₂^?) and hydroxyl radicals (?OH) participated in TC-HCl removal process, which is different from the pure BiVO₄ reaction system. Hence, the present work can provide a new approach for the formation of novel plasmonic photocatalysts with high photoactivity and can act as effective practical application for environmental remediation.     

杭州湾北岸36种挥发性有机物污染特征及来源解析

为研究杭州湾北岸VOCs（挥发性有机物）的浓度水平、组成特征、反应活性和潜在来源,采用GC-FID在线监测系统对杭州湾北岸环境大气中的36种VOCs开展了为期1 a（2017年12月-2018年11月）的连续观测,采用LOH（VOCs的·OH消耗速率）和OFP（O₃生成潜势）2种方法估算了大气VOCs的反应活性,并利用PMF（正定矩阵因子分解）和CPF（条件概率函数）模型分析其来源.结果表明:①φ（VOCs）小时平均值在冬季（26.47×10-9）最高,夏季（9.76×10-9）最低;全年φ（VOCs）小时平均值为21.24×10-9,其中烷烃、烯烃+炔烃、芳香烃、卤代烃的贡献率分别为33.24%、34.13%、15.63%、17.00%;φ（烷烃）、φ（芳香烃）和φ（卤代烃）呈较明显的昼夜变化特征,φ（烯烃）和φ（炔烃）无明显昼夜变化趋势.②大气VOCs的总LOH和OFP分别为9.39 s-1和220.57 μg/m3,KOH（·OH反应速率常数）和MIR（最大增量反应活性）系数的平均值分别为17.34×10-12 cm3/（molecule·s）和3.31;KOH和MIR系数的平均值分别与间/对-二甲苯的KOH和乙苯的MIR系数接近,表明大气VOCs的化学反应活性较强;VOCs关键活性物种为异戊二烯、乙烯、丙烯、甲苯、二甲苯和顺-2-丁烯.③特征物种相关性分析表明,杭州湾北岸大气存在老化现象,异戊烷和正戊烷受煤燃烧源影响较大,二甲苯和乙苯受溶剂排放源影响较大,甲苯和苯除受机动车尾气影响外,还受其他排放源影响.④PMF和CPF模型来源分析表明,大气VOCs主要来自石化工业源、燃料挥发源、生物质燃烧和煤燃烧源、机动车排放源和溶剂使用源,其中,机动车排放源主要来自西北方向,其他源主要来自西北、西和西南方向.研究显示,杭州湾北岸大气VOCs来源复杂,受周边工业区的影响较大.      

Chemical characteristics of road dust PM2.5 fraction in oasis cities at the margin of Tarim Basin

In order to understand the compositions characteristics of particulate matter with aerodynamic diameter less than 2.5 μm (PM_2.5) fraction in road dust (RD_2.5) of oasis cities on the edge of Tarim Basin, 30 road dust (RD) samples were collected in Kashi, Cele, and Yutian in the spring, 2018, and RD_2.5 was collected using the resuspension approach. Eight water-soluble ions, 39 trace elements and 8 fractions of carbon-containing species in PM_2.5 were analyzed. Ca²⁺ and Ca were the most abundant ions and elements in RD_2.5 (7.1% and 9.5%). Cl^- in RD_2.5 was affected not only by attributed to saline-alkali soils in oasis cities of the Tarim Basin and dust from Taklimakan Desert but also by human activities. Moreover, the organic carbon/elemental carbon (OC/EC) ratio indicated that carbon components in RD_2.5 in Cele town mainly come from fossil fuel combustion, while those in Yutian and Kashi mainly come from biomass combustion. It is noteworthy that high Ca in RD_2.5 was seriously affected by anthropogenic emissions, and high Na and K contents in RD_2.5 could be derived from soil and desert dust. It was estimated that Cd, Tl, Sn and Cr were emitted from anthropogenic emissions using the enrichment factor. The coefficients of divergence (COD) result indicated that the influence of local emission on road dust emission is greater than that of long-distance transmission. This study is the first time to comprehensively analyze the chemical characteristics of road dust in oasis cities, and the results provides the sources of road dust at the margin of Tarim Basin.     

固体样品六价铬的检测比对和验证

采用碱溶液提取/火焰原子吸收法(HJ 687—2014《固体废物六价铬的测定 碱消解/火焰原子吸收分光光度法》和HJ 1082—2019《土壤和沉积物 六价铬的测定 碱溶液提取-火焰原子吸收分光光度法》)测定了固体废物和土壤样品中六价铬含量,比对和验证了2种方法实验流程、分析方法性能及不确定度评定结果。结果表明:HJ 687—2014的方法检出限相对较高,不适合测定浓度较低的土壤;HJ 1082—2019要求按照试样制备的步骤配置工作曲线,考虑了基体干扰的影响。HJ 687—2014的检出限为0.28 mg/kg,相对标准偏差为0.69%~0.93%,样品加标回收率为95.7%~97.2%;HJ 1082—2019的检出限为0.17 mg/kg,相对标准偏差为0.6%~3.0%,样品加标回收率为76.0%~83.1%。对于同一实际样品,2种方法的测定结果相近,HJ 687—2014和HJ 1082—2019的测定结果分别为(48.1±4.2),(46.6±5.4) mg/kg。比对发现,影响HJ 687—2014和HJ 1082—2019不确定度的最主要环节分别为曲线拟合和样品消解。     

圆红冬孢酵母利用生物柴油副产物粗甘油产油脂的影响因素分析

以餐饮废油制备生物柴油的副产物粗甘油为碳源,采用圆红冬孢酵母发酵生产微生物油脂。通过对发酵影响因素的优化,确定了最适发酵条件为:种子复苏时长24 h、富集时长10 h、接种量为6%、初始粗甘油浓度为60 g/L、C/N为60、有机氮占总氮比例为75%、发酵体积为100 mL、发酵温度为30 ℃、发酵时间为6 d,在此条件下,获得总产油量为10.56 g/L,油脂产率为0.229。与无机氮源硫酸铵相比,有机氮源蛋白胨的添加显著提高了油脂含量和总产油量。通过测定油脂的脂肪酸成分并利用Hoekman方程估算所得生物柴油的性能指标,表明其符合中国、美国及欧盟标准。该方法既为粗甘油的再利用提供了一条新途径,又为生物柴油的生产提供了廉价的原材料。     

关于在长江经济带布局以水质改善为目标的流域生态缓冲体系的思考

生态缓冲带能够有效减缓流域内的人类活动或自然过程对水环境和水生态系统的影响.在长江经济带构建流域生态缓冲体系,对长江生态保护修复具有十分重要的意义.讨论了构建流域生态缓冲体系涉及的生态缓冲带位置选择、缓冲体系所占最低面积比率、宽度划定等一些基本的原则要求;利用卫星遥感影像数据,提取各汇水单元的地形特征、土地利用类型特征、土壤类型、土壤侵蚀强度、水文水系等数据,对长江经济带流域生态缓冲体系进行布局.结果表明:①长江经济带内林草地是主要土地利用类型,占区域总面积的62.46%,但是分布很不均匀,主要集中在西部高地和中下游的丘陵地带,在人口密集、农田密集的区域分布偏少;城镇用地主要集中在长江中下游地区.②土壤类型空间差异显著,浙江省、江苏省、湖南省、江西省及安徽省大部分区域的土壤多是黏性比较大,污染物迁移能力较低;而污染物迁移能力较强的砂质土或者土层较薄的山地草甸土主要分布在四川省北部、西北部.水力侵蚀、风力侵蚀和冻融侵蚀均有分布,且以水力侵蚀为主,建议在中度及以上侵蚀强度区域尽量减少污染源,重点布置缓冲带,增加该区域的缓冲力度.③长江经济带范围内可以利用的中小型湿地、小型河流支浜的面积至少有1.4×104 km2,再结合林草缓冲带,就可以形成一个生态缓冲体系.④在土地利用类型分布结果基础上,叠加土壤侵蚀强度和水系分布,将污染源区、中度及以上侵蚀强度区、水体区作为缓冲对象,建立缓冲体系的重点区域,总面积约14.26×104 km2,占长江经济带总面积的6.95%.对照欧美地区的研究,6.95%的缓冲体系面积占比是偏低的,需要在长江经济带开展深入研究来确定适宜的缓冲体系面积比,推进长江经济带流域生态缓冲体系的构建.